Differences

This shows you the differences between two versions of the page.

--- tutorials:radiation-model-in-crop_model8 [2025/05/28 10:11] – barley1965
+++ tutorials:radiation-model-in-crop_model8 [2025/10/29 21:56] (current) – barley1965
@@ Line 4: / Line 4: @@
 //Open {{tutorials:GrowManyFruits.gsz|GrowManyFruits.gsz}}//
-We have now introduced a virtual plant canopy, initially consisting of 12 plants (three rows of 4 plants each). The number of plants per row is fixed in line 82 of the code:
+This model produces a virtual plant canopy, initially consisting of 16 plants (four rows of four plants each). When you run the model, you will get the 3D visual output and also some curves (in the chart "MODEL OUTPUT") indicating the dynamics of several yield-related state variables: light absorbed by lower and upper leaves, light absorbed by soil, number of shed leaves, number of flowers and fruits, and the assimilates produced by lower and upper leaves (where ranks 1 - 4 are lower leaves, and ranks 5 - 9 are upper leaves). At this stage you are not supposed to understand all the workings of the model, the objective of this exercice is for you to play the grower and to change a limited number of agronomic and genetic parameters (planting density, plant architecture).
+The parameters you may change in the code can be found in Example1.rgg, lines 5 - 13:
-const int PL_NO = 4;
+<code java>
+/* Parameters you may change: */
+public @Editable @Range(min=90,max=200) float GOLDEN_ANGLE = 137.5; //137.5;
+public @Editable @Range(min=30,max=90) float BRANCH_ANGLE = 50;//50
+float LEAF_ANGLE = BRANCH_ANGLE+10; //70
+const float LEAF_CURVATURE = 2; //between 1 and 5
+const float LEAF_FOLDING = 20; //20 between 0 and 50
+public @Editable @Range(min=9,max=20) int PHYLLOCHRON = 9; //15  between 9 and 20
+public @Editable @Range(min=1,max=5) int PL_NO = 4; //5
+public @Editable @Range(min=1,max=5) int ROW_NO = 4; //4
+public @Editable @Range(min=1,max=10) int FINAL_LEAF_SIZE = 4; //4
+</code>
+However, it is also possible (and much easier?) to use the sliders for this: click on the tab Meta Objects (bottom left) then you will see in the Attribute Editor window (almost) the same parameters:
-Task: run the model, and see how many fruits you get in the end.
+{{:tutorials:sliders.png?400|}}
-By changing plant density, can you increase the number of fruits?
+//Task: run the model, and see how many fruits you get in the end!
+By changing plant density, can you increase the number of fruits?//
-Next, you may increase or decrease branching angle, leaf angle, final leaf size, leaf curvature, leaf folding, and phyllochron by up to 20 per cent to optimize fruit yield (L. 76 – 81):
+Next, you may increase or decrease branching angle, leaf angle, final leaf size, leaf curvature, leaf folding, and phyllochron by up to 20 per cent to optimize fruit yield. Note that you cannot change leaf curvature and leaf folding from the slider panel, you need to modify the code and recompile.
-N.B.: Do not forget to recompile after each change in the code!
+N.B.: After having changed values with the slider, you have to press the ''Reset'' button for the new values to take effect, then press the ''Run Grow'' button. If you recompile the code (by saving Example1.rgg"), the default parameters (L. 5-12) will be chosen again!
+Finally, note that this model is just a training tool (toy...), and not based on any measurements of real plants!
+{{tutorials:growmanyfruits1.png?175x175}} {{tutorials:growmanyfruits2.png?180x180}} {{tutorials:growmanyfruits3.png?180x180}} {{tutorials:growmanyfruits5.png?175x175}}
+{{tutorials:growmanyfruits4.png?200x200}} {{tutorials:growmanyfruits6.png}}